Protable Mini 12V Welding Machine 18650 Battery Spot Welder Supply Nickel Sheet

Description

Home
Payment
Shipping
About us
Contact us
Store Categories
Store Categories
Other
Details
Spot Welding Machine Series
Transistor spot welding machine WM-01
Portable
5000MAH
Built-in battery
Portable 4300MAH Built-in battery
Transistor spot welding machine WM-02 Upgrade
5MOS 12V Battery Spot Welder Kit
4MOS 12V Battery Spot Welder Kit
1、Transistor spot welding machine WM-01
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
2、
Portable
5000MAH
Built-in battery
1. Introduction
This product is suitable for daily or small spot welding/butt welding work in the family. It is automatically triggered without a switch, and the operation is convenient and quick.
2. Parameters
Battery capacity: 5AH
Output voltage: 4.2V max
Output current: maximum 500A
Design current: maximum 1000A
Input parameters: 5V/2.1A
Support welding: 0.1-0.2 nickel sheet, iron sheet, stainless steel
Welding time: several milliseconds
Charging voltage: 4.5~5.5V (current≥2.5A)
Product size: 150*80*22MM
Shell material: hard aluminum alloy
Weight: a set of 467g
3. Features
⑵Simple operation
⑶ Hard appearance
⑷Easy to use
4. Components introduction
5. How to use
Power on
Click button 6
Shut down
Double-click the button6；
Automatically shut down after three minutes of standby
Gear position adjustment
Button 7 is gear position adjustment, click to change gears, the cycle is first gear>second gear>third gear>fourth gear>standby
Standby
After the fourth gear, click to enter the standby state;
It enters the standby state without spot welding for more than 30 minutes.
Spot welding
After turning on the machine, select the required gear and touch the welding object with the welding pen to spot welding.
Precautions for spot welding
a. Please fix the spot welding items in the spot welding mode;
b. Please keep the welding objects in a flat state;
3. Keep cooling time about 10S after welding
6. Matters needing attention
⑴It can be operated while charging, and it will enter standby mode when charging
⑵It is recommended to charge it once half a year when it is not used for a long time, and the charge is 75%
⑶ Continuous use of the soldering pen will cause hotness, it is recommended to wear gloves to operate
⑷Do not drop, flood, heat and other harmful operations to electronics
⑸The blackening of the tip of the soldering pen will affect the effect, which can be worn off with sandpaper
⑹If the spot welding is too long or the shutdown is caused by good contact, just restart it
Package Included:
1PCS * Hand-held desktop mini portable spot welder
3、
Portable 4300MAH Built-in battery
Product introduction:
This spot welder is only about 400g, which is very small and much smaller than a mobile phone.
Don't think that a small body is of no use. Pointing a 0.1 or 0.12 is not a problem, repairing an 18650 battery pack, assembling a lithium battery, a small case, no problem at all!
In terms of hardware, two batteries with extremely low internal resistance are used! With 600A discharge capacity! 5 levels of output, capable of handling various scenarios! At the same time, it has low voltage protection, overcurrent protection, and overcharge protection! Fully protect the battery! Longer life!
It also has a 2.1A hand-charged flash charging function. Spot welding machines are not commonly used, but power banks are always useful. When they are not spot welding, they can also be used as power banks! One machine with multiple uses! Great value!
Not only that, it also has the function of fast charging for itself, other homes use 1A charging current, and my home’s charging is also 2.1A fast charging! Compared to other homes, my home charges twice as fast!
Features:
This product uses 2 lithium batteries with extremely low internal resistance, and uses the special algorithm of the single-chip microcomputer to instantaneously discharge the high-temperature molten nickel sheet to quickly fit on the metal material! It can weld common batteries on the market, such as: 18650 26650 and other lithium batteries. The machine has low-voltage protection, over-current protection, charging protection, and its own high-current fast charging power bank function. Compared with similar products on the market, it has many unique advantages!
Package Included:
Portable spot welding machine host×1
Quick release spot welding pen×2
Micro USB charging cable x1
4、
Transistor spot welding machine WM-02 Upgrade
Product introduction:
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.
3: Screen description and parameter adjustment.
4: Welding
Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.
Specifications:
Material: Metal
Input line length: app.20cm/7.87in
Length of welding pen: app.30cm/11.81in
Color: Red+Blue+Black
Battery: lithium battery(not included)
Quantity: 1Set
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
5、
5MOS 12V Battery Spot Welder Kit
Product introduction:
Specifications:
This spot welder circuit board can be used to weld 18650 / 26650 / 32650 lithium batteries. Advantages: portable, stable, reliable and durable. Low cost, own car start battery, or high-power battery pack, can be connected to use! Save production costs!
Function keys: 1, for switching machine, 2 for shifting gear!
Turn on the power, the default is the first gear. Press the button for 2 seconds to release,
When the gear is increased by one gear, the buzzer rings and the LED flashes
For example: in the third gear, the buzzer rings three times and the LED flashes three times
There are 5 gears in total. The spot welding strength is gradually strengthened from the 1st to 5th gear, and the 5th gear is the strongest!
After the 5th gear, press and hold the key again. It will turn off. If you press the key for a long time, it will turn on. At the same time, the gear will return to the first gear
Users need to provide 12V battery power supply, welding current is about 100A ~ 200A, for the common 0.1mm ~ 0.15mm nickel plate welding is easy. Please make sure that your battery can have a current greater than 100A, otherwise it will not be able to weld!
Power supply voltage: 11.5v-14.8v
Working current: 100-200a (optimal current: 150A, discharge below 100A, will not work)
The battery with large discharge current will directly affect the welding effect. The following batteries are recommended:
36-45ah lead-acid battery with good performance and low internal resistance (internal resistance less than 10 milliohm, discharge current greater than 100 a), such as new car starting battery!
About 4000mAh 35c-8000mah 30C 3S aviation model lithium battery pack
18650 battery pack with 30-35ah capacity
Power requirements:
Spot welding is based on the principle of high current local rapid heating and cooling, which requires sufficient current supply. Generally, the welding current of 0.1-0.15 nickel plate is about 90-150a, so the working power supply of circuit board must be greater than or equal to 150A
The following battery pack can be used as working power supply
12V automobile starting power supply, aircraft model 3S high rate battery pack, three series high rate lithium battery pack, Hitachi 40900 3 series battery pack, 12V 20A lead-acid battery with good performance.
Package Included:
1 circuit board (V5)
2 welding pens 2
3 input wires 2
4 screws, 3 sets
5 buzzer 1
6 capacitors 1
7 nickel sheet 1 m
6、
4MOS 12V Battery Spot Welder Kit
Product introduction:
Product Features
Lightweight and portable, stable and reliable, wear-resistant, and can provides long service time.
Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by a short circuit.
Fuse the nickel sheet firmly with the battery.
And it is precisely controlled by the single-chip microcomputer program without a trigger switch.
Adopt screw fix, more stable, and more reliable.
The welding current approx. 90-130A, which is more than enough to welding a common 0.1mm-0.12mm nickel plate.
Upgraded to automatically triggered design, do not need to press the button for a long time anymore, completely frees your hands.
Note
Power supply requirements:
It is forbidden to use the power supply of the farad capacitor, and it is forbidden to use the lead-acid battery or lithium battery pack of 60A or above.
System voltage: 12V-14.6V (capacity X rate = must be greater than 150A)
Current requirements: 150A or more instantaneous output (such as car starter power supply, 3S RC high-power battery pack, 20A lead-acid battery with good performance above 20A)
Misunderstanding: Don't think that you can use 3 series 18650 series to supply power. After all, the conventional 18650 only has a 3-5C discharge rate, so each section can only provide
2.5A*3=7.5A load capacity, which is far from 150A unless 20 Parallel connection, 3 series, and 60 sections of 18650 are possible, but it is obviously unrealistic.
The battery pack that can start the car can basically meet the power supply requirements of this circuit.
The following battery packs can be used as working power:
1. 12V car starter power supply
2. Model 3S high rate battery pack
3. 3 string high rate lithium battery pack
4. Hitachi 40900 3-string battery pack
5. 12V 20A and above lead-acid battery with good performance
Switch function: press switch for 1.5 seconds to turn on (green light flash, output low power spot welding pulse every 3 seconds), press switch for 1.5 seconds (blue light flash, output medium power spot welding pulse every 3 seconds), press switch 1.5 Seconds (red light flash, high power spot welding pulse output every 3 seconds) Press the switch for 1.5 seconds to shut down.