Mini Spot Welder Machine 18650 Battery Various Welding Power Supply USA Stock

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Mini Spot Welder Machine 18650 Battery Various Welding Power Supply USA Stock
Popular
Popular
Product Introduction
Spot Welding Machine Series
Transistor spot welding machine WM-01
5000MAH 18650 Lithium Battery
4300MAH  Lithium Battery
1、Transistor spot welding machine WM-01
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
2、5000MAH 18650 Lithium Battery
1. Introduction
This product is suitable for daily or small spot welding/butt welding work in the family. It is automatically triggered without a switch, and the operation is convenient and quick.
2. Parameters
Battery capacity: 5AH
Output voltage: 4.2V max
Output current: maximum 500A
Design current: maximum 1000A
Input parameters: 5V/2.1A
Support welding: 0.1-0.2 nickel sheet, iron sheet, stainless steel
Welding time: several milliseconds
Charging voltage: 4.5~5.5V (current≥2.5A)
Product size: 150*80*22MM
Shell material: hard aluminum alloy
Weight: a set of 467g
3. Features
⑵Simple operation
⑶ Hard appearance
⑷Easy to use
4. Components introduction
5. How to use
Power on
Click button 6
Shut down
Double-click the button6；
Automatically shut down after three minutes of standby
Gear position adjustment
Button 7 is gear position adjustment, click to change gears, the cycle is first gear>second gear>third gear>fourth gear>standby
Standby
After the fourth gear, click to enter the standby state;
It enters the standby state without spot welding for more than 30 minutes.
Spot welding
After turning on the machine, select the required gear and touch the welding object with the welding pen to spot welding.
Precautions for spot welding
a. Please fix the spot welding items in the spot welding mode;
b. Please keep the welding objects in a flat state;
3. Keep cooling time about 10S after welding
6. Matters needing attention
⑴It can be operated while charging, and it will enter standby mode when charging
⑵It is recommended to charge it once half a year when it is not used for a long time, and the charge is 75%
⑶ Continuous use of the soldering pen will cause hotness, it is recommended to wear gloves to operate
⑷Do not drop, flood, heat and other harmful operations to electronics
⑸The blackening of the tip of the soldering pen will affect the effect, which can be worn off with sandpaper
⑹If the spot welding is too long or the shutdown is caused by good contact, just restart it
Package Included:
1PCS * Hand-held desktop mini portable spot welder
3、4300MAH  Lithium Battery
Product introduction:
This spot welder is only about 400g, which is very small and much smaller than a mobile phone.
Don't think that a small body is of no use. Pointing a 0.1 or 0.12 is not a problem, repairing an 18650 battery pack, assembling a lithium battery, a small case, no problem at all!
In terms of hardware, two batteries with extremely low internal resistance are used! With 600A discharge capacity! 5 levels of output, capable of handling various scenarios! At the same time, it has low voltage protection, overcurrent protection, and overcharge protection! Fully protect the battery! Longer life!
It also has a 2.1A hand-charged flash charging function. Spot welding machines are not commonly used, but power banks are always useful. When they are not spot welding, they can also be used as power banks! One machine with multiple uses! Great value!
Not only that, it also has the function of fast charging for itself, other homes use 1A charging current, and my home’s charging is also 2.1A fast charging! Compared to other homes, my home charges twice as fast!
Features:
This product uses 2 lithium batteries with extremely low internal resistance, and uses the special algorithm of the single-chip microcomputer to instantaneously discharge the high-temperature molten nickel sheet to quickly fit on the metal material! It can weld common batteries on the market, such as: 18650 26650 and other lithium batteries. The machine has low-voltage protection, over-current protection, charging protection, and its own high-current fast charging power bank function. Compared with similar products on the market, it has many unique advantages!
Package Included:
Portable spot welding machine host×1
Quick release spot welding pen×2
Micro USB charging cable x1
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Mini Spot Welder Machine 18650 Battery Various Welding Power Supply USA Stock
Product Introduction
Spot Welding Machine Series
Transistor spot welding machine WM-01
5000MAH 18650 Lithium Battery
4300MAH  Lithium Battery
1、Transistor spot welding machine WM-01
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
2、5000MAH 18650 Lithium Battery
1. Introduction
This product is suitable for daily or small spot welding/butt welding work in the family. It is automatically triggered without a switch, and the operation is convenient and quick.
2. Parameters
Battery capacity: 5AH
Output voltage: 4.2V max
Output current: maximum 500A
Design current: maximum 1000A
Input parameters: 5V/2.1A
Support welding: 0.1-0.2 nickel sheet, iron sheet, stainless steel
Welding time: several milliseconds
Charging voltage: 4.5~5.5V (current≥2.5A)
Product size: 150*80*22MM
Shell material: hard aluminum alloy
Weight: a set of 467g
3. Features
⑵Simple operation
⑶ Hard appearance
⑷Easy to use
4. Components introduction
5. How to use
Power on
Click button 6
Shut down
Double-click the button6；
Automatically shut down after three minutes of standby
Gear position adjustment
Button 7 is gear position adjustment, click to change gears, the cycle is first gear>second gear>third gear>fourth gear>standby
Standby
After the fourth gear, click to enter the standby state;
It enters the standby state without spot welding for more than 30 minutes.
Spot welding
After turning on the machine, select the required gear and touch the welding object with the welding pen to spot welding.
Precautions for spot welding
a. Please fix the spot welding items in the spot welding mode;
b. Please keep the welding objects in a flat state;
3. Keep cooling time about 10S after welding
6. Matters needing attention
⑴It can be operated while charging, and it will enter standby mode when charging
⑵It is recommended to charge it once half a year when it is not used for a long time, and the charge is 75%
⑶ Continuous use of the soldering pen will cause hotness, it is recommended to wear gloves to operate
⑷Do not drop, flood, heat and other harmful operations to electronics
⑸The blackening of the tip of the soldering pen will affect the effect, which can be worn off with sandpaper
⑹If the spot welding is too long or the shutdown is caused by good contact, just restart it
Package Included:
1PCS * Hand-held desktop mini portable spot welder
3、4300MAH  Lithium Battery
Product introduction:
This spot welder is only about 400g, which is very small and much smaller than a mobile phone.
Don't think that a small body is of no use. Pointing a 0.1 or 0.12 is not a problem, repairing an 18650 battery pack, assembling a lithium battery, a small case, no problem at all!
In terms of hardware, two batteries with extremely low internal resistance are used! With 600A discharge capacity! 5 levels of output, capable of handling various scenarios! At the same time, it has low voltage protection, overcurrent protection, and overcharge protection! Fully protect the battery! Longer life!
It also has a 2.1A hand-charged flash charging function. Spot welding machines are not commonly used, but power banks are always useful. When they are not spot welding, they can also be used as power banks! One machine with multiple uses! Great value!
Not only that, it also has the function of fast charging for itself, other homes use 1A charging current, and my home’s charging is also 2.1A fast charging! Compared to other homes, my home charges twice as fast!
Features:
This product uses 2 lithium batteries with extremely low internal resistance, and uses the special algorithm of the single-chip microcomputer to instantaneously discharge the high-temperature molten nickel sheet to quickly fit on the metal material! It can weld common batteries on the market, such as: 18650 26650 and other lithium batteries. The machine has low-voltage protection, over-current protection, charging protection, and its own high-current fast charging power bank function. Compared with similar products on the market, it has many unique advantages!
Package Included:
Portable spot welding machine host×1
Quick release spot welding pen×2
Micro USB charging cable x1
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.